收藏本站
Caution
1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm.
2. The soldering iron should not directly touch the inductor.
5. Cleaning
◆Cleaning conditions
1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux
Precautions
Technical
considerations
used and purpose of the cleaning（e.g. to remove soldering flux or other materials from the production process.）
2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's
characteristics.
◆Cleaning conditions
1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation
of the inductor's electrical properties（especially insulation resistance）.
2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimentally affect the performance of the inductors.
（1） Excessive cleaning
a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the
cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions
should be carefully checked;
Ultrasonic output Below 20W/?
Ultrasonic frequency Below 40kHz
Ultrasonic washing period 5 min. or less
6. Post cleaning processes
◆Application of resin coatings, moldings, etc. to the PCB and components.
1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the inductor's performance.
Precautions
2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat
may lead to inductor damage or destruction.
3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors.
The use of such resins, molding materials etc. is not recommended.
7. Handling
◆Breakaway PC boards（splitting along perforations）
1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection
or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆General handling precautions
1. Always wear static control bands to protect against ESD.
2. Keep the inductors away from all magnets and magnetic objects.
Precautions
3. Use non-magnetic tweezers when handling inductors.
4. Any devices used with the inductors（ soldering irons, measuring instruments） should be properly grounded.
5. Keep bare hands and metal products（i.e., metal desk）away from chip electrodes or conductive areas that lead to chip electrodes.
6. Keep inductors away from items that generate magnetic fields such as speakers or coils.
◆Mechanical considerations
1. Be careful not to subject the inductors to excessive mechanical shocks.
（1） If inductors are dropped on the floor or a hard surface they should not be used.
（2） When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other
boards or components.
8. Storage conditions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
Recommended conditions
Precautions
Technical
considerations
Ambient temperature Below 40℃
Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions inductor electrode solderability decreases as
time passes, so inductors should be used within 6 months from the time of delivery.
*The packaging material should be kept where no chlorine or sulfur exists in the air.
◆Storage
1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of
terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within
6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors.
? This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E02R01
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CKD31C101H153M CAP FEEDTHRU 15000PF 50V 1206
CKD710JB0J474S CAP FEEDTHRU .47UF 6.3V 0402
CKG57NX7S1C107M CAP CER 100UF 16V 20% X7S 2220
CKP2012N2R2M-T INDUCTOR 2.2UH MULTILAYER 0805
CLLC1AX7S0G334M CAP CER 0.33UF 4V 20% X7S 0603
CLS5D11HPNP-100NC INDUCTOR PWR 1000MA 10UH SMD PB
CM201212-1R0KL INDUCTOR CHIP 1UH 10% SMD
CM21X5R106K06AL CAP CER 10UF 4V 10% X5R 0805
相关代理商/技术参数
CK-2125-R68MTK 制造商:KEMET 制造商全称:Kemet Corporation 功能描述:Surface Mount Ferrite Products
CK21KW/MNS 制造商:BM Connecting Cables 功能描述:COTTON GLOVES (MENS)
CK21KW/MNS-20 制造商:BM Connecting Cables 功能描述:LIGHT COTTON GLOVES
CK21M 功能描述:PIPE CLAMP PROBE RoHS:是 类别:测试设备 >> 测试引线 - 热电偶，温度探头 系列:CK 标准包装:1 系列:6543 类型:J 型热电偶 使用:液体，半固体 尖端 - 类型:防浸渍 / 穿透式，圆头 插头类型:超微型（热电偶插头） 探针温度范围:-40 ~ 2000°F（-40 ~ 1093°C） 线缆长度:- 线缆绝缘:- 插头颜色:黑 探针长度:12.000"（304.80mm） 探针材料:-
CK21MC1 功能描述:2 EACH PIPE CLAMP PROBES RoHS:是 类别:测试设备 >> 测试引线 - 热电偶，温度探头 系列:CK 标准包装:1 系列:6543 类型:J 型热电偶 使用:液体，半固体 尖端 - 类型:防浸渍 / 穿透式，圆头 插头类型:超微型（热电偶插头） 探针温度范围:-40 ~ 2000°F（-40 ~ 1093°C） 线缆长度:- 线缆绝缘:- 插头颜色:黑 探针长度:12.000"（304.80mm） 探针材料:-
CK2233 制造商:Lorlin Electronics Ltd 功能描述:
CK2252 制造商:Lorlin Electronics Ltd 功能描述:
CK22803 制造商:Chenbro Micom Usa, Inc. 功能描述:6G 28 PORT SAS EXPANDER CARD, WITH BRACKET - Bulk